New Products

The switching voltage regulator SBEC 30D EX is supposed to function as a current supply for receivers and servos. It enables to use a wide range of input voltages from 2S up to 15S Li-XX cells. Setup of the output voltage between 5 and 8.4V is accomplished in the JETI transmitter via EX Bus connection or through JETIBOX. This implies that the SBEC is also prepared for use with new "higher" voltage servos. The SBEC 30D is suitable for medium and larger model due to its maximum current of 30A.

The Expander SW4 is an extension for magnetic and RC switches and is designed for switching multiple devices simultaneously. The JETI model company produces a wide range of devices that can be switched by magnetic switch or RC switch. The Expander SW4 allows you to combine the switching duties so that several devices can be controlled using one only element. Furthermore, some outputs are optically isolated to prevent interference. This makes it is possible to isolate control of devices which may be sensitive to electric interference.

The Magnetic switch is an electronic switching device designed to be used as a switch for JETI model products. A big advantage of electronic switches in comparison to mechanical switches is that, in general, electronic switches are highly resistant to vibration. Also, virtually an unlimited number of ON and OFF cycles is guaranteed with an electronic switch. Because electronic switches have no mechanically movable elements, contacts etc. to wear out, an extremely long service life is another important feature. Unlike with mechanical switches, electronic switches cannot be unexpectedly or falsely tripped.

12 channel full-range receiver with integrated Assist stabilization, compatible with JETI EX & EX Bus protocols. Supports telemetry functions and contains a separate battery power connector (MPX).

 

10 channel full-range receiver with integrated Assist stabilization, compatible with JETI EX & EX Bus protocols. Supports telemetry functions and stabilization for airplane and multicopter models.

 

7 channel full-range receiver with integrated Assist stabilization, compatible with JETI EX & EX Bus protocols. Supports telemetry functions and stabilization for airplane and multicopter models.

 

6 channel full-range receiver with integrated Assist stabilization, compatible with JETI EX & EX Bus protocols. Supports telemetry functions and stabilization for airplane and multicopter models.

 

The MULi6s Module is a sensor designed to monitor the Li-XX battery voltage, which measures the voltage of each battery cell via the balance connector. It allows you to monitor the voltage of up to 6 Li-XX cells per module. The individual MULi6s modules can be serialized and can be connected to up to 5 modules.

The DITEX TD1609S servo delivers 162 Ncm (8,4V) at a speed of 0,08sec / 60° and includes all the innovative DITEX technologies. These servos are perfect for everything from 3D helicopters, giant scale aerobats and monster scale models where ultimate reliability, strength and flexible programming are required.

The DITEX TD0807W is truly a special wing servo. Very compact, extremely durable, the TD0807W is the ultimate solution for hotliners, gliders, and jets where a very low-profile servo is required. A true strength of 72 Ncm and a speed of 0,07sec / 60 ° make the DITEX Wing servo one of the quickest, strongest and safest servos for these demanding applications.

 

The DITEX TD0905L bring all of the DITEX engineering to the low profile / standard size form factor.  The lower height, of course, allows racers to take advantage of the TD0905L’s series true and reliable  85 Ncm of torque at 8,4 V. The sensational speed of 0,05sec / 60° and maximum precision of the DITEX encoder chip make this servo one of the quickest servos in the market. Don’t forget, all the innovative programmable functionalities of the DITEX series are packed into the TD0905L too!

 

DITEX TD2612S is the king of DITEX ultra torque servos.  Delivering an incredible 265 Ncm (8,4V) of torque at a speed of 0,12sec / 60 ° while requiring an amazingly modest amp draw.  These servos will get the job done with authority and won’t bring the power supply to its knees.  Of course, all of DITEX TD2612S is the king of DITEX ultra torque servos.

 

Powerful MEZON PRO controllers can be used in a wide variety of applications. They come with strong BEC, full JETI Duplex EX telemetry and programmability via the Device Explorer of JETI Duplex DS/DC transmitters. Forward/reverse motor operation is also possible.

LMR (Limited Motor Run) - the controller is especially designed for glider models. The continuous motor run is limited to a few seconds.

Powerful MEZON PRO controllers can be used in a wide variety of applications. They come with strong BEC, full JETI Duplex EX telemetry and programmability via the Device Explorer of JETI Duplex DS/DC transmitters. Forward/reverse motor operation is also possible.

LMR (Limited Motor Run) - the controller is especially designed for glider models. The continuous motor run is limited to a few seconds.

Powerful MEZON PRO controllers can be used in a wide variety of applications. They come with strong BEC, full JETI Duplex EX telemetry and programmability via the Device Explorer of JETI Duplex DS/DC transmitters. Forward/reverse motor operation is also possible.

 

Powerful MEZON PRO controllers can be used in a wide variety of applications. They come with strong BEC, full JETI Duplex EX telemetry and programmability via the Device Explorer of JETI Duplex DS/DC transmitters. Forward/reverse motor operation is also possible.

Powerful MEZON PRO controllers can be used in a wide variety of applications. They come an optocoupler, full JETI Duplex EX telemetry and programmability via the Device Explorer of JETI Duplex DS/DC transmitters. Forward/reverse motor operation is also possible.

Powerful MEZON PRO controllers can be used in a wide variety of applications. They come an optocoupler, full JETI Duplex EX telemetry and programmability via the Device Explorer of JETI Duplex DS/DC transmitters. Forward/reverse motor operation is also possible.

The Central Box is a switchboard designed for the complete management of servos in a model with an emphasis on safety. The Central Box 210 offers maximal unreduced power for each servo (servo outputs do not have overload protection). The Central Box can manage up to two batteries and fully supports the JETI EX telemetry system. Up to three receivers with serial (PPM, EX Bus, S.BUS, UDI) output can be connected to the Central Box 210. With JETI DC/DS transmitter, the full potential of the Central Box can be used, such as an easy way to configure the Central Box, EX telemetry, and very fast servo response.