News

Limited edition of DC/DS-24

We would like to introduce you a special limited edition of ten DC/DS-24 transmitters, which was created for the 75th anniversary of the end of World War II. Unfortunately, the release of this series last year was significantly affected by a global pandemic, which also affected our plans. The limited edition is intended for end customers, collectors and fans of JETI and is created in the spirit of flying legends of World War II. Each transmitter has original design, which was artistically painted directly on the transmitter (Airbrush).

You can find more information and photos on our Facebook profile JETI Model.

Two updates have been released via JETI Studio.

1. REX Assist v1.19 (03/2021)
Airplane pitch with Assist enabled is no longer affected by acceleration (Horizon mode).

2. MVario2 FAI F5J v2.05 (03/2021)
Supports new sensor revision.

Central Box update v1.10

New version of SW v1.10 intended for Central Box 210/220.

-Time interval of the RX alarm was modified to 2s.
-Extension the compatibility for Futaba R7008SB (S.BUS)

The update can be done by the Jeti Studio.

More news »

Measure Sensors EX

Products with label EX are completed by a range of new functions, which grew on the base of many years of experience and valuable knowledge in this category.

Sensors labelled with EX offer improved basic functions as well as new extending functions.

Improved display arrangement of more telemetric values
Support of fully graphical display of telemetric data
Easier administration of the equipment
Improved user comfort of telemetric data processing with the aid of the JETIBOX Profi or PC, …
Possibility of telemetric data storage with the aid of the JETIBOX profi or PC, …
PC online telemetry with the aid of the JETI FlightMonitor program
Compatible with all receivers/transmitter modules JETI Duplex
Compatible to the JETIBOX/JETIBOX mini
Firmware update using PC

Ordering

Ordering type

Show

MUI200 EX

Art. No.: JEX-MUI-200

Assignment of the MUI EX sensor is measurement of voltage, current and consumed capacity of flight batteries in the model. The wireless data transmission by the DUPLEX 2,4GHz system is monitored by the JETIBOX terminal.

MUI30 EX

Art. No.: JEX-MUI-30

MUI50 EX

Art. No.: JEX-MUI-50

MUI75 EX

Art. No.: JEX-MUI-75

MULi 6s EX

Art. No.: JEX-MULI6S

MULi 6S EX is a sensor for checking voltage of Li-XX batteries that checks the voltage by service connector of every single cell. It allows you to check the voltage up to 6 Li-XX cells.

MULi6s Module

Art. No.:

The MULi6s Module is a sensor designed to monitor the Li-XX battery voltage, which measures the voltage of each battery cell via the balance connector. It allows you to monitor the voltage of up to 6 Li-XX cells per module. The individual MULi6s modules can be serialized and can be connected to up to 5 modules.

MVario2 EX

Art. No.: JEX-MV2

MVario2 EX is a system that measures atmospheric pressure and using the obtained data it calculates the altitude above sea level, airspeed, and the rate of climb as well as the rate of descent. Changes in climb and descent rates are signaled as well. The sensor also alerts you if any alarm setting is exceeded. The sensor data can also be transmitted via the Duplex system to the user.

SBEC 30D EX

Art. No.: J-SBEC-30-D

The switching voltage regulator SBEC 30D EX is supposed to function as a current supply for receivers and servos. It enables to use a wide range of input voltages from 2S up to 15S Li-XX cells. Setup of the output voltage between 5 and 8.4V is accomplished in the JETI transmitter via EX Bus connection or through JETIBOX. This implies that the SBEC is also prepared for use with new "higher" voltage servos. The SBEC 30D is suitable for medium and larger model due to its maximum current of 30A.

		1 2 21 - 28 from: 28



Customer support: Phone/Fax: +420 556 802 092 between 8:00 - 10:00 (CET) \| E-mail: jeti@jetimodel.com \| Web: www.jetimodel.com