rss
RSS
csende
Search
News
Limited edition of DC/DS-24
Image

 

 

 

We would like to introduce you a special limited edition of ten DC/DS-24 transmitters, which was created for the 75th anniversary of the end of World War II. Unfortunately, the release of this series last year was significantly affected by a global pandemic, which also affected our plans. The limited edition is intended for end customers, collectors and fans of JETI and is created in the spirit of flying legends of World War II. Each transmitter has original design, which was artistically painted directly on the transmitter (Airbrush).

You can find more information and photos on our Facebook profile JETI Model.

 

 

 

Two updates have been released via JETI Studio.
Image

 

 

 

1.    REX Assist v1.19 (03/2021)
Airplane pitch with Assist enabled is no longer affected by acceleration (Horizon mode).

2.    MVario2 FAI F5J v2.05 (03/2021)
Supports new sensor revision.

Central Box update v1.10
Image
New version of SW v1.10 intended for Central Box 210/220.

-Time interval of the RX alarm was modified to 2s.
-Extension the compatibility for Futaba R7008SB (S.BUS)

The update can be done by the Jeti Studio.

ADVANCE pro

The ADVANCE pro controller family contains our entire motor control experience since last several years. These controllers will fully comply with all requirements of the users and in connection with the programming card they will fulfill even the most ambitious wishes. The programming card (ProgCard Pro) is compatible with controllers of the ADVANCE plus line and the ADVANCE pro line.


As a standard features, the controllers offer heat protection, battery low discharge protection as well as current limitation. The controllers Advance XX Pro and Advance XX Pro SB contain an integrated stabilized current supply (BEC) for receivers and servos.

The controllers of the Advance XX Pro Opto type are not equipped with this kind of supply and must be furnished with an independent current supply as for instance a battery of 4 x NiXX or an external stabilized current supply. The Opto-Controllers provide a galvanic separation between the power drive (motor, controller, flight battery) and the receiver with servos. We recommend the application of opto-controllers in cases where the BEC circuit becomes unable to fulfill your demands (current supply of a larger number of servos and the unavoidability of a seperate current source) as well as in models with higher current consumption and higher input voltages.

Ordering type
Show

Advance 10 Pro

Art. No.: JA-10-P
Advance 10 Pro

The Advance Pro controllers will fully comply with all requirements of the user and in connection with the programming card they will fulfill even the most ambitious wishes. The programming card (ProgCard Plus) is compatible with controllers of the Advance Plus line and simultaneously with the Advance Pro line.

 

Advance 12 Pro

Art. No.: JA-12-P-P
Advance 12 Pro

The Advance Pro controllers will fully comply with all requirements of the user and in connection with the programming card they will fulfill even the most ambitious wishes. The programming card (ProgCard Plus) is compatible with controllers of the Advance Plus line and simultaneously with the Advance Pro line.

 

Advance 30 Pro SB

Art. No.: JA-30-P-P-SB
Advance 30 Pro SB

The Advance Pro controllers will fully comply with all requirements of the user and in connection with the programming card they will fulfill even the most ambitious wishes. The programming card (ProgCard Plus) is compatible with controllers of the Advance Plus line and simultaneously with the Advance Pro line.

Switching BEC.

 

Advance 40 Pro opto

Art. No.: JA-40-P-P-O
Advance 40 Pro opto

The Advance Pro controllers will fully comply with all requirements of the user and in connection with the programming card they will fulfill even the most ambitious wishes. The programming card (ProgCard Plus) is compatible with controllers of the Advance Plus line and simultaneously with the Advance Pro line.

The Opto-Controllers provide a galvanic separation between the power drive (motor, controller, flight battery) and the receiver with servos.

Advance 40 Pro SB HS

Art. No.: JA-40-P-P-SB-HS
Advance 40 Pro SB HS

The Advance Pro controllers will fully comply with all requirements of the user and in connection with the programming card they will fulfill even the most ambitious wishes. The programming card (ProgCard Plus) is compatible with controllers of the Advance Plus line and simultaneously with the Advance Pro line.

SB: Switching BEC.

HS: High Speed. Suitable for high RPM motors.

 

Advance 70 Pro opto

Art. No.: JA-70-P-P-O
Advance 70 Pro opto

The Advance Pro controllers will fully comply with all requirements of the user and in connection with the programming card they will fulfill even the most ambitious wishes. The programming card (ProgCard Plus) is compatible with controllers of the Advance Plus line and simultaneously with the Advance Pro line.

The Opto-Controllers provide a galvanic separation between the power drive (motor, controller, flight battery) and the receiver with servos.

Advance 70 Pro SB HS

Art. No.: JA-70-P-P-SB-HS
Advance 70 Pro SB HS

The Advance controllers will fully comply with all requirements of the user and in connection with the programming card, they will fulfill even the most ambitious wishes. The programming card (ProgCard Plus) is compatible with controllers of the Advance Plus line and simultaneously with the Advance Pro line.

SB: Switching BEC.

HS: High Speed. Suitable for high RPM motors.

 

Advance 77 Pro opto

Art. No.: JA-77-P-P-O
Advance 77 Pro opto

The Advance Pro controllers will fully comply with all requirements of the user and in connection with the programming card they will fulfill even the most ambitious wishes. The programming card (ProgCard Plus) is compatible with controllers of the Advance Plus line and simultaneously with the Advance Pro line.

The Opto-Controllers provide a galvanic separation between the power drive (motor, controller, flight battery) and the receiver with servos.

Advance 90 Pro opto

Art. No.: JA-90-P-P-O
Advance 90 Pro opto

The Advance Pro controllers will fully comply with all requirements of the user and in connection with the programming card they will fulfill even the most ambitious wishes. The programming card (ProgCard Plus) is compatible with controllers of the Advance Plus line and simultaneously with the Advance Pro line.

The Opto-Controllers provide a galvanic separation between the power drive (motor, controller, flight battery) and the receiver with servos.

Partners
Alltron.ch Esprit Hacker Hepf

JETI Italia Topmodel.fr
www.pimpyourjeti.de jetiforum JETI magazin egadgets
Opale

Customer support:

Phone/Fax: +420 556 802 092 between 8:00 - 10:00 (CET)     |     E-mail: jeti@jetimodel.com     |     Web: www.jetimodel.com