News

Limited edition of DC/DS-24

We would like to introduce you a special limited edition of ten DC/DS-24 transmitters, which was created for the 75th anniversary of the end of World War II. Unfortunately, the release of this series last year was significantly affected by a global pandemic, which also affected our plans. The limited edition is intended for end customers, collectors and fans of JETI and is created in the spirit of flying legends of World War II. Each transmitter has original design, which was artistically painted directly on the transmitter (Airbrush).

You can find more information and photos on our Facebook profile JETI Model.

Two updates have been released via JETI Studio.

1. REX Assist v1.19 (03/2021)
Airplane pitch with Assist enabled is no longer affected by acceleration (Horizon mode).

2. MVario2 FAI F5J v2.05 (03/2021)
Supports new sensor revision.

Central Box update v1.10

New version of SW v1.10 intended for Central Box 210/220.

-Time interval of the RX alarm was modified to 2s.
-Extension the compatibility for Futaba R7008SB (S.BUS)

The update can be done by the Jeti Studio.

More news »

AC Speed Controllers

The speed controllers are available in 2 main types; for brushed motors (DC – commutator) and for brushless motors BLDC. Other factors in the selection of the controller are the voltage range of the drive batteries, current demands of the motor, and the method used to power the receiver and servos. Jeti speed controllers normally provide thermal protection, protection of the battery against low voltage (LVC), and over current protection. BEC (Battery Eliminator Circuit) controllers include an integrated circuit to provide a stabilized power supply to power the receiver and servos.

Controllers that do not have BEC are marked OPTO, and require the use of a receiver battery (4 or 5 x NiXX), or an external BEC (Jeti MAX BEC is recommended for use with up to 12 cell NiXX, 3S LiPo, or 4S A123). OPTO controllers are designed to provide complete electrical isolation of the power supply from the radio system. OPTO controllers are recommended when BEC circuits are not sufficient for your needs because of a high servo count, the use of digital servos, or for models with high current consumption or high operating voltage.

Individual lines of controllers	Application	Types according to current [A]	Types according to voltage [V]	BEC	Parameter adjustment possibilities	Telemetry
ECO	Beginners	12 - 25	5 - 16	linear	Jumper	No
ADVANCE	Advanced	4 - 90	5 - 42	linear	Prog Card	No
HiCOPTER	Multicopter	30 - 90	5 - 42	-	-	No
MASTER	Specials for Hacker	4 - 195	5 - 42	linear	Prog Box	No
SPIN	Demanding applications	11 - 200	5-59	switching	JETIBOX	JETIBOX
MEZON	High power airplanes and helis	75 - 165	6-59	switching	JETIBOX	JETIBOX, EX
MEZON PRO	High power airplanes (hotliner)	40 - 80	5 - 51	switching	JETIBOX / JETI transmitters	JETIBOX, EX Bus

ADVANCE proHiCOPTERSPIN proMEZONMEZON PRO

Ordering

Ordering type

Show

Advance 10 Pro

Art. No.: JA-10-P

The Advance Pro controllers will fully comply with all requirements of the user and in connection with the programming card they will fulfill even the most ambitious wishes. The programming card (ProgCard Plus) is compatible with controllers of the Advance Plus line and simultaneously with the Advance Pro line.

Advance 12 Pro

Art. No.: JA-12-P-P

Advance 30 Pro SB

Art. No.: JA-30-P-P-SB

Switching BEC.

Advance 40 Pro opto

Art. No.: JA-40-P-P-O

The Opto-Controllers provide a galvanic separation between the power drive (motor, controller, flight battery) and the receiver with servos.

Advance 40 Pro SB HS

Art. No.: JA-40-P-P-SB-HS

SB: Switching BEC.

HS: High Speed. Suitable for high RPM motors.

Advance 70 Pro opto

Art. No.: JA-70-P-P-O

The Opto-Controllers provide a galvanic separation between the power drive (motor, controller, flight battery) and the receiver with servos.

Advance 70 Pro SB HS

Art. No.: JA-70-P-P-SB-HS

The Advance controllers will fully comply with all requirements of the user and in connection with the programming card, they will fulfill even the most ambitious wishes. The programming card (ProgCard Plus) is compatible with controllers of the Advance Plus line and simultaneously with the Advance Pro line.

SB: Switching BEC.

HS: High Speed. Suitable for high RPM motors.

Advance 77 Pro opto

Art. No.: JA-77-P-P-O

The Opto-Controllers provide a galvanic separation between the power drive (motor, controller, flight battery) and the receiver with servos.

Advance 90 Pro opto

Art. No.: JA-90-P-P-O

The Opto-Controllers provide a galvanic separation between the power drive (motor, controller, flight battery) and the receiver with servos.

Advance Pro ProgCard

Art. No.: JA-PPPC

The programming card ProgCard Pro is determined for adjustments of the Advance Plus controller family (on the side of the programming card you will find the inscription Advance ProgCard plus), as well as for adjustments of the Advance Pro controller (on the side of the programming card you will find the inscription Advance ProgCard Pro).

HiCOPTER 30A opto

Art. No.: J-HIC-30-O

Speed controllers of HiCOPTER product line are aimed for controlling and regulating BLDC motors that are used for driving multicopters. These controllers are pre-set from the manufacturer for the cooperation with stabilization systems used in copters. The controllers accept control signal with a frequency up to 500Hz and they respond to the needed change of revolutions from control/stabilization unit of the copter.

HiCOPTER 40A opto

Art. No.: J-HIC-40-O

HiCOPTER 70A opto

Art. No.: J-HIC-70-O

HiCOPTER 77A opto

Art. No.: J-HIC-77-O

HiCOPTER 90A opto

Art. No.: J-HIC-90-O

MEZON 115 opto (RPM)

Art. No.: Standard: JM- 115-O, RPM: JM- 115-O-RPM

Jeti MEZON ESC´s advanced design and software are capable of unique precise and efficient motor control. Our MEZON ESC´s are able to be fully integrated with the DUPLEX EX systems. With the DUPLEX integration, all data are measured in real time. Mezon ESC´s were designed to be able to measure the exact battery capacity used and let you set up a motor cut off point based not only on cell voltage, but also on overall battery pack capacity.

The OPTO line of MEZON Brushless ESC´s feature an optically separated radio signal from the power management circuitry which guarantees an interference-free operation. The OPTO line of brushless ESCs does not contain any BEC circuit.