Duplex 2.4 EX

MSPEED 450 EX is a sensor which measures the speed of a flying model through the air to provide the indicated airspeed (IAS). The reporting of airspeed can be very instructive with regard to the control of a flying model, for example allowing the pilot to determine the model´s stall speed and set an alarm to indicate when the model falls below this speed.

Maximum speed: 450km/h

EnLink 2RS plus is a device for increasing safety and reliability of radio controled models to the highest level. Parallel connection of systems that are detached maximally leads to the significant increase in reliability. EnLink 2RS Plus is constructed especially for installing to systems with parallel sorting of two receivers in the model.

EnLink 2RS Plus is capable of merging the servo signals as well a PPM, UDI or EX Bus protocols. 

Receiver DUPLEX R7 nano EX combines many servo outputs together with small dimensions. R7 nano EX is designed for easy use in small models. The receiver incorporates a single 32mm antenna.

R7 nano is the lightest receiver of the Duplex system, its weight is only 1 gram (2g in shrink tube).

Main Switch is an electronic switch designed primarily for switching of the main power supply for an RC model. It adds an element of safety when handling the model, without the need to physically disconnect the model´s batteries. A big advantage of electronic switches in comparison to mechanical switches is, in general, their higher reliability as far as vibration resistance is concerned. The Main Switch prevents the connectors from sparking when connecting the batteries, thus it can also replace Anti Spark plugs. 

Main Switch is an electronic switch designed primarily for switching of the main power supply for an RC model. It adds an element of safety when handling the model, without the need to physically disconnect the model´s batteries. A big advantage of electronic switches in comparison to mechanical switches is, in general, their higher reliability as far as vibration resistance is concerned. The Main Switch prevents the connectors from sparking when connecting the batteries, thus it can also replace Anti Spark plugs. 

MBar EX is a sensor that measures the excess pressure in non-corrosive and unionized gases and liquids. The sensor records the maximum and minimum measured values of pressure and temperature. Moreover, it is possible to set the alarm for high pressure or pressure drop. The information from the sensor is transmitted to the user via Duplex system. The MBar EX can be used e.g. for measuring pressure in containers with compressed air (retractable undercarriage systems) or for controlling the oil pressure in hydraulic systems.

12 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions and contains a separate battery power connector.

Additional features:

• PPM input
• PPM output
• Integrated expander for EX & EX Bus devices
• UDI digital output

10 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

Additional features:

• PPM input
• PPM output
• Integrated expander for EX & EX Bus devices
• UDI digital output

7 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

Additional features:

• PPM input
• PPM output
• Integrated expander for EX & EX Bus devices
• UDI digital output

6 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

Additional features:

• PPM input
• PPM output
• Integrated expander for EX & EX Bus devices
• UDI digital output

MAlti EX is a system that measures atmospheric pressure and using the obtained data it calculates the altitude above sea level and relative altitude above the ground. The sensor also alerts you if any alarm setting is exceeded. The sensor data can also be transmitted via the Duplex system to the user.

7 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions. Antenna length 40cm.

Additional features:

• PPM input
• PPM output
• Integrated expander for EX & EX Bus devices
• UDI digital output

The MFlow2 Turbine 800 is a telemetry sensor that measures the flow of the pumped fuel and calculates its amount in the tank. The MFlow2-Turbine is a variant designed for the models powered by a jet engine, with consumption up to 800ml/min.

The MFlow2 Turbine 3000 is a telemetry sensor that measures the flow of the pumped fuel and calculates its amount in the tank. The MFlow2-Turbine is a variant designed for the models powered by a jet engine, with consumption up to 3000ml/min.

The MFlow2 Gas 800 is a telemetry sensor that measures the flow of the pumped fuel and calculates its amount in the tank. The MFlow2-Gasoline is a variant for the models powered by glow or gasoline motors.

The MRPM HALL EX sensor provides RPM and power level readings using magnetic Hall Effect and rare earth magnet. The MRPM HALL sensor measures the rotation speed and performance of the rotating surface and provides warnings when pre-set parameters are exceeded. All information is transmitted in real time using JETI Duplex telemetry system.

3 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

Additional features:

• PPM input
• PPM output
• Integrated expander for EX & EX Bus devices
• UDI digital output

Full-range backup receiver compatible with JETI EX 900 & EX Bus protocols. Supports telemetry functions.

Additional features:

• PPM input
• PPM output
• Integrated expander for EX & EX Bus devices
• UDI digital output

12 channel full-range receiver with integrated Assist stabilization, compatible with JETI EX & EX Bus protocols. Supports telemetry functions and contains a separate battery power connector (MPX).

 

10 channel full-range receiver with integrated Assist stabilization, compatible with JETI EX & EX Bus protocols. Supports telemetry functions and stabilization for airplane and multicopter models.