Accessories

The USB Adapter transfers information between a PC and Jeti model products. It is, in fact, an adaptation means between the PC USB interface and the data connector Ext. with appropriate USB support, provided in Jeti model products. All types of equipment marked with the label symbol USBa are prepared for firmware updates. On the internet pages www.jetimodel.com you may find information about actual firmware versions.

The Magnetic switch is an electronic switching device designed to be used as a switch for JETI model products. A big advantage of electronic switches in comparison to mechanical switches is that, in general, electronic switches are highly resistant to vibration. Also, virtually an unlimited number of ON and OFF cycles is guaranteed with an electronic switch. Because electronic switches have no mechanically movable elements, contacts etc. to wear out, an extremely long service life is another important feature. Unlike with mechanical switches, electronic switches cannot be unexpectedly or falsely tripped.

The Expander SW4 is an extension for magnetic and RC switches and is designed for switching multiple devices simultaneously. The JETI model company produces a wide range of devices that can be switched by magnetic switch or RC switch. The Expander SW4 allows you to combine the switching duties so that several devices can be controlled using one only element. Furthermore, some outputs are optically isolated to prevent interference. This makes it is possible to isolate control of devices which may be sensitive to electric interference.

The DPS 40 (twin electronic switch) and SPS 20 (single electronic switch) are electronic switches mainly meant to switch supply voltages of receivers / servos, regulators, fuel pumps or similar equipment. A big advantage of electronic switches in comparison to mechanical ones is in general their higher reliability as far as vibration resistance is concerned. Another advantage of the electronic switch is given by its practical ability to withstand an unlimited number of switching cycles.

The switch SP 06 opto has been specifically designed for switching purposes of auxiliary functions, such as on board glow plug heating systems and miscellaneous lighting systems etc. in model airplanes, model ships, and model cars. The switched loads can be of ohmic, inductive or capacitive character. The switching moment is signalled by  a LED.

The switch SP 06 has been specifically designed for switching purposes of auxiliary functions, such as on board glow plug heating systems and miscellaneous lighting systems etc. in model airplanes, model ships and model cars. The switched loads can be of ohmic, inductive or capacitive character. The switching moment is signalled by a LED.

SingleBEC is a linear regulator to provide power for a standard servo with a maximum input voltage of 6V. The SingleBEC can also be used to provide power for the control units of helicopters or multi-rotor aircraft.  

The switching voltage regulator SBEC is supposed to function as a current supply for receivers and servos. It enables to use a wide range of input voltages from 3S up to 12S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This implies that the SBEC is also prepared for use with new „higher“ voltage servos. The SBEC is suitable for medium and larger model due to its maximum current of 40A.

The switching voltage regulator SBEC 30D EX is supposed to function as a current supply for receivers and servos. It enables to use a wide range of input voltages from 2S up to 15S Li-XX cells. Setup of the output voltage between 5 and 8.4V is accomplished in the JETI transmitter via EX Bus connection or through JETIBOX. This implies that the SBEC is also prepared for use with new "higher" voltage servos. The SBEC 30D is suitable for medium and larger model due to its maximum current of 30A.

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This implies that the SBEC is also prepared for use with new „higher“ voltage servos. The SBEC is due to its maximum current of 12A suitable for medium and larger models.

RCDroidBox allows real-time monitoring and recording of telemetry data transferred using JETI Duplex or Duplex EX protocol. The system consists of both hardware and a software part. The hardware is the actual RCDroidBox Bluetooth adapter and the software is an application running on a device with the Android operating system, such as cell phone or tablet.

RCDroidBox allows real-time monitoring and recording of telemetry data transferred using JETI Duplex or Duplex EX protocol. The system consists of both hardware and a software part. The hardware is the actual RCDroidBox Bluetooth adapter and the software is an application running on a device with the Android operating system, such as cell phone or tablet.

Power-Ion 5200 battery pack is designed to power JETI model transmitters of the DC and DS lines. The battery is equipped with plugs. Charging is done via the transmitter and the adapter that comes with the transmitter.

Power-Ion accumulators 2600,2900 – 2S1P a 5200,5800 – 2S2P are battery packs suitable to power the receiver and servos in the model.

Power-Ion accumulators 2600,2900 – 2S1P a 5200,5800 – 2S2P are battery packs suitable to power the receiver and servos in the model.

JETI model supplies packs of 2100 and 2600 mAh accumulators. Selected cells in pack are connected by a soldering process that is considered a basic prerequisite of a longtime stability.

JETI model supplies packs of 2100 and 2600 mAh accumulators. Selected cells in pack are connected by a soldering process that is considered a basic prerequisite of a longtime stability.

Replacement temperature sensing probe for MT 125.

Manufactured according to very high European standards, the MAX BEC 2D plus EX is the latest dual input, linear voltage regulator from JETI. The Max BEC 2D Plus EX includes a magnetic switch, so there is no mechanical wear-and-tear from switching the unit on and off.

The MAX BEC 2D plus EX supports on / off via RC Switch. It can be easily installed.

MAX BEC 2 is designed to power the receiver and servos in the model. MAX BEC 2 is a linear voltage stabilizer with an adjustable output voltage. The output voltage is set using a jumper and in one of four positions: 5.0V, 5.4V, 5.7V or 6.0V. MAX BEC 2 can be powered using NiXX and Li–XX cells. MAX BEC also gives an indication of used capacity of the battery with four LED´s.