Accessories

The DPS 40 (twin electronic switch) and SPS 20 (single electronic switch) are electronic switches mainly meant to switch supply voltages of receivers / servos, regulators, fuel pumps or similar equipment. A big advantage of electronic switches in comparison to mechanical ones is in general their higher reliability as far as vibration resistance is concerned. Another advantage of the electronic switch is given by its practical ability to withstand an unlimited number of switching cycles.

DSM 10 is an electronic switch for switching of two receiver batteries which are connected to one receiver. The product also includes a receiver current supply switch. Batteries that are connected to the inputs of the DSM 10 are permanently measured and connected with the aid of a hysteresis comparator either both to the output, or one of both batteries with the higher voltage only.

The DSM 10 exit consists of a MPX connector which can be used for direct connection of the exit to the receiver. The MPX connector is a fixed part of Duplex receivers with the label EPC (External Power Connector), receivers R14 and R18.

DSM ESC is an electronic switch for powering receiver and servos. It combines the voltage output from either two electronic speed controllers (ESC), each with a BEC circuit or an ESC in combination with a receiver battery. The throttle signal from the receiver is supplied to both controllers simultaneously. The DSM ESC also includes a receiver power supply switch.

EnLink 2RS plus is a device for increasing safety and reliability of radio controled models to the highest level. Parallel connection of systems that are detached maximally leads to the significant increase in reliability. EnLink 2RS Plus is constructed especially for installing to systems with parallel sorting of two receivers in the model.

EnLink 2RS Plus is capable of merging the servo signals as well a PPM, UDI or EX Bus protocols. 

The switching voltage regulator HiCOPTER is supposed to act as a current supply for accessories in the XCopters. The switching voltage regulators HiCOPTER 12V make it possible to use wide range of input voltages from 4S up to 12S Li-XX cells.

The switching voltage regulator HiCOPTER is supposed to act as a current supply for accessories in the XCopters. The switching voltage regulators HiCOPTER 12V make it possible to use wide range of input voltages from 4S up to 12S Li-XX cells.

Increaser MPX male / 3x JR conector for MAX BEC 2. Conductor cross section 0.5 mm2.

JETIBOX is a universal communication terminal which can be used with any JETI products that are marked JETIBOX Compatible. JETIBOX Compatible (JBC) products use powerful software to allow easy setup and reading of data using a simple menu driven display on the JETIBOX terminal.

JETIBOX Holder

The JETIBOX mini is used for data readout and parameter adjustment of hooked up equipment. Due to small size it can be easily mounted to the transmitter and its clearly arranged backlit display enables excellent readability at any weather coditions. Equipment designated by the JETIBOX COMPATIBLE label is JETIBOX mini compatible as well.

The JETIBOX profi is a mobile wireless device, offering maximum comfort to the user while viewing, processing, and storing telemetric data. An integral part of the JETIBOX profi is the system JETI DUPLEX 2.4GHz that can be alternatively operated in one of the two offered wireless modes.

Main Switch is an electronic switch designed primarily for switching of the main power supply for an RC model. It adds an element of safety when handling the model, without the need to physically disconnect the model´s batteries. A big advantage of electronic switches in comparison to mechanical switches is, in general, their higher reliability as far as vibration resistance is concerned. The Main Switch prevents the connectors from sparking when connecting the batteries, thus it can also replace Anti Spark plugs. 

Main Switch is an electronic switch designed primarily for switching of the main power supply for an RC model. It adds an element of safety when handling the model, without the need to physically disconnect the model´s batteries. A big advantage of electronic switches in comparison to mechanical switches is, in general, their higher reliability as far as vibration resistance is concerned. The Main Switch prevents the connectors from sparking when connecting the batteries, thus it can also replace Anti Spark plugs. 

Linear regulator MAX BEC is a sophisticated tool for regulating voltage in models which have a receiver and servos powered by 2 LiXX cells or 5-6 NiXX cells. Servo voltage is constant during the entire flight which results in smooth motion of the servos.

MAX BEC 2 is designed to power the receiver and servos in the model. MAX BEC 2 is a linear voltage stabilizer with an adjustable output voltage. The output voltage is set using a jumper and in one of four positions: 5.0V, 5.4V, 5.7V or 6.0V. MAX BEC 2 can be powered using NiXX and Li–XX cells. MAX BEC also gives an indication of used capacity of the battery with four LED´s.

Manufactured according to very high European standards, the MAX BEC 2D plus EX is the latest dual input, linear voltage regulator from JETI. The Max BEC 2D Plus EX includes a magnetic switch, so there is no mechanical wear-and-tear from switching the unit on and off.

The MAX BEC 2D plus EX supports on / off via RC Switch. It can be easily installed.

Replacement temperature sensing probe for MT 125.

JETI model supplies packs of 2100 and 2600 mAh accumulators. Selected cells in pack are connected by a soldering process that is considered a basic prerequisite of a longtime stability.

JETI model supplies packs of 2100 and 2600 mAh accumulators. Selected cells in pack are connected by a soldering process that is considered a basic prerequisite of a longtime stability.

Power-Ion accumulators 2600,2900 – 2S1P a 5200,5800 – 2S2P are battery packs suitable to power the receiver and servos in the model.