rss
RSS
csende
Search
News
Limited edition of DC/DS-24
Image

 

 

 

We would like to introduce you a special limited edition of ten DC/DS-24 transmitters, which was created for the 75th anniversary of the end of World War II. Unfortunately, the release of this series last year was significantly affected by a global pandemic, which also affected our plans. The limited edition is intended for end customers, collectors and fans of JETI and is created in the spirit of flying legends of World War II. Each transmitter has original design, which was artistically painted directly on the transmitter (Airbrush).

You can find more information and photos on our Facebook profile JETI Model.

 

 

 

Two updates have been released via JETI Studio.
Image

 

 

 

1.    REX Assist v1.19 (03/2021)
Airplane pitch with Assist enabled is no longer affected by acceleration (Horizon mode).

2.    MVario2 FAI F5J v2.05 (03/2021)
Supports new sensor revision.

Central Box update v1.10
Image
New version of SW v1.10 intended for Central Box 210/220.

-Time interval of the RX alarm was modified to 2s.
-Extension the compatibility for Futaba R7008SB (S.BUS)

The update can be done by the Jeti Studio.

Accessories

 JETIBOX profi

Accessories

Additional accessories and electronics - available are are voltage stabilizers, electronic switches, LiIon accumulators, JETIBOX programmers and many more.

 

Ordering type
Show

AddCAP 10AS

Art. No.: J-AC-10AS
AddCAP 10AS

The AddCAP 10AS is an add-on capacitor unit that helps to insure constant voltage for your servos and receiver in large pulse current consumption power systems. 

AddCAP 1640

Art. No.: J-AC-1640
AddCAP 1640

AddCAP 1640 is an add-on capacitor unit designed to enhance battery power supply for drive systems using low-impedence electric motors (1-2 turns). It should also be used when the wires from your battery to your ESC need to be lengthened more than 20cm (8 inches). 

 

AddCAP 820

Art. No.: J-AC-820
AddCAP 820

AddCAP 820 is an add-on capacitor unit designed to enhance battery power supply for drive systems using low-impedence electric motors (1-2 turns). It should also be used when the wires from your battery to your ESC need to be lengthened more than 20cm (8 inches). 

 

Advance Pro ProgCard

Art. No.: JA-PPPC
Advance Pro ProgCard
The programming card ProgCard Pro is determined for adjustments of the Advance Plus controller family (on the side of the programming card you will find the inscription Advance ProgCard plus), as well as for adjustments of the Advance Pro controller (on the side of the programming card you will find the inscription Advance ProgCard Pro).

Antenna 2.4 - 2.5 GHz, 2 dBi

Art. No.: JMS-A2400
Antenna 2.4 - 2.5 GHz, 2 dBi
Replacement antenna for DUPLEX 2.4 GHz transmitter module.

Antenna extension cable for TF/TG/TGi modules

Art. No.: JMS-PA
Antenna extension cable for TF/TG/TGi modules
Antenna extension cable for TF/TG/TGi modules

Anti Spark 4,0mm

Art. No.: JMS-ASC4
Anti Spark 4,0mm

Anti Spark 5,5mm

Art. No.: JMS-ASC5
Anti Spark 5,5mm

Anti Spark 8mm

Art. No.: JMS-ASC8
Anti Spark 8mm

Assembly Kit FFC 16 (for Futaba FC-16 and FC-18 transmitters)

Art. No.: JMS-F16
Assembly kit for installation DUPLEX TU transmit module into Futaba FC-16 and FC-18 transmitters.

Assembly Kit G10/12 (for Graupner MC 10/12 transmitters)

Art. No.: JMS-G10/12
Assembly Kit G10/12 (for Graupner MC 10/12 transmitters)
Assembly kit for installation DUPLEX TU transmit module into Graupner MC-10 and MC-12 transmitters.

Assembly Kit G19 (for Graupner MC-19 transmitters)

Art. No.: JMS-G19
Assembly Kit G19 (for Graupner MC-19 transmitters)
Assembly kit for installation DUPLEX TU transmit module into Graupner MC-19 transmitter.

Assembly kit GMC 15/16-20

Art. No.:
Assembly kit GMC 15/16-20
Assembly kit for installation DUPLEX TU2 transmit module into Graupner MC-14, MC-15, MC-16, MC16-20 transmitters.

Assembly kit GMX 16 (for Graupner MX 12s/16s transmitters)

Art. No.: JMS-G16
Assembly kit GMX 16 (for Graupner MX 12s/16s  transmitters)
Assembly kit for installation DUPLEX TU transmit module into Graupner MX-16s and MX-12s transmitters.

Assembly kit HE7

Art. No.: JMS-HE7
Assembly kit HE7
Mounting kit for transmitters Hitec Eclipse 7

Assembly kit JB profi

Art. No.: JMS-JBP
Assembly kit JB profi
Assembly kit is designed for mechanical and electrical connection between JETIBOX profi and RC transmitter.

Connection
red: plus
black: minus
yellow: PPM

Assembly kit ME

Art. No.: JMS-ME
Assembly kit ME
Mounting kit for the transmitter DUPLEX TU MULTIPLEX EVO.

Assembly kit SWTU2

Art. No.: JMS-SWTU2
Assembly kit SWTU2
Mounting kit for the transmission module Duplex TU2 for switching between the two modules.

Assembly kit VOICE-1

Art. No.: JMS-VOICE-1
Assembly kit VOICE-1
Mounting kit for connecting an external siren and headphone output of the DUPLEX TU2.

Assembly kit: Cable for the TU-2 module

Art. No.: JMS-KTU
Assembly kit: Cable for the TU-2 module
The cable supplied with the  Duplex TU-2 EX  transmitter module. It is used to connect the Duplex TU-2  EX transmitter module and Graupner transmitters (eg. MC-22). Cable length 200 mm.
Partners
Alltron.ch Esprit Hacker Hepf

JETI Italia Topmodel.fr
www.pimpyourjeti.de jetiforum JETI magazin egadgets
Opale

Customer support:

Phone/Fax: +420 556 802 092 between 8:00 - 10:00 (CET)     |     E-mail: jeti@jetimodel.com     |     Web: www.jetimodel.com